Browse by Category
  
Search  
Aptela Knowledge Base » Call Tree / IVR » Hold Music & Audio » How to Remove "Please hold while I locate your party. You may press pound (#) at any time to go directly to voicemail" Audios

How to Remove "Please hold while I locate your party. You may press pound (#) at any time to go directly to voicemail" Audios

"Please hold while I locate your party. You may press pound at any time to go directly to voicemail" is made up two separate audio settings. This allows you full control over your audio subsystem. Follow the directions below to remove or modify either of those audio prompts.


Custom Transfer Message Settings
"Please hold" or "Please hold while I locate your party" is the default Custom Transfer Messages for each user and department.  The default audio can be silenced or replaced with another wav file.  Note: the audio format for the replacement audio must be 8kHz, 8-bit, Mono wav.

To edit the default audio for Users:
  1. Log in to the Aptela account either as the User or as the Account Operator
    • Users:
      • Select Settings
      • Click on My Account
    • Account Operators: 
      • Select People from the Navigation Bar
      • Click the name for the user(s) you wish to make changes to
  2. Scroll down and click on Call Customization
  3. Next to Custom Transfer Message, check "Do Not Use" to silence the default message.  To replace the message, "Browse" for the audio on your hard drive and click "Enabled."  To restore the default message either un-check "Do Not Use" or "Enabled"
  4. Click Save at the bottom of the page
*****

To edit the default audio for Departments:
  1. Log in to the Aptela account as the Operator
    • Department Managers can log in with their User name and password
  2. Click People on the Navigation Bar
  3. Click the Departments tab
  4. Click the name of the department you wish to make changes to
  5. Scroll down to Call Customization section
  6. Next to Custom Transfer Message, check "Do Not Use" to silence the default message.  To replace the message, "Browse" for the audio on your hard drive and click "Enabled."  To restore the default message either un-check "Do Not Use" or "Enabled"
  7. Click Save at the bottom of the page

Settings for "You may press pound at any time to go directly to voicemail"
"You may press pound at any time to go directly to voicemail" is an account wide setting. To change this setting for the entire account:
  1. Log in to the Aptela account as the Operator
  2. Click Settings on the Navigation Bar
  3. Click "Transfer Options" under Directory Settings section
  4. Check Disable "Press pound to go directly to voicemail" to remove audio.  Un-check to restore audio.
  5. Click Save

Email    Print


How helpful was this article to you?

Related Articles

article How to Record your own Custom Audios

Once you have written the script for your custom audio (e.g. Call Tree, Custom Transfer Message), you are ready to record the audio(s). All audio...
  2006.08.23    Views: 12694   

article How to Send Incoming Calls Directly to Voicemail

Users and Departments can send all incoming calls directly to voicemail using the Web portal.  This is useful if you do not want calls to ring...
(No rating)  2006.09.11    Views: 10418   

article How to Retrieve Custom Audios you Recorded

After you record your custom audios, you will be ready to retrieve your recordings via the web portal or your voicemail notification.*  If you...
  2008.03.17    Views: 9768   

article What Do I Do if My Phone is Showing the Wrong Time?

If your phone is showing the wrong time (for example - after Daylight Savings Time switch), it's possible that the time zone is not correctly set...
(No rating)  2009.06.04    Views: 3991   

article How to Change your Account Hold Music/Message

Only the Account Operator has the ability to manage the account hold music.Log into www.aptela.com/my-account as the Account OperatorSelect...
  2006.08.23    Views: 7757